• owners manual MODEL NO. 113.20680 Serial Number Model and serial number may be found on a plate attached to your infeed table. You should record both CRRFTSMRNo model and serial number in a safe place for future use. 6_- INCH JOIN TER-PLA NER CAUTION.

Download Manual for Model 113206801 CRAFTSMAN 6 1/8-INCH JOINTER-PLANER.Sears PartsDirect has parts, manuals & part diagrams for all types of repair projects. View and Download CRAFTSMAN 113.20680 owner's manual online. 113.20680 Planer pdf manual. FULL ONE YEAR WARRANTY ON CRAFTSMAN JOINTER/PLANER This.

Download Manual for Model 351217240 CRAFTSMAN JOINTER/PLANER.Sears PartsDirect has parts, manuals & part diagrams for all types of repair projects.

• FULL ONE YEAR WARRANTY ON CRAFTSMAN JOINTER/PLANER This warranty_giVes you specific legal rights; and you may:alsohave other rights which vary from state to state. ROEBUCK BSC 41-3 SEARS TOWE R CHICAGO, I L 60684 general safety instructions for power. • additionaB safety instructions for iointer-paaner Safety is a combination of operator common sense and 9. PROTECTION: EYES, HANDS, FACE, EARS, BODY alertness at all times when the Jointer-Ptaner is being used. If any part of your jointer is malfunctioning, has been WARNING: FOR YOUR OWN SAFETY.

• Sharpening Cutter Blades.Checking Cutterblade Screws.GENERAL MAINTENANCE.Installing Sliding Guard.WIRING DIAGRAM.Mounting Recommended Craftsman Motor and LUBRICATION.Belt Guards.TROUBLE SHOOTING. Check Motor Rotation. RECOMMENDED ACCESSORIES.Jointer-Pulley Belt Guard Installation. • ]-HE RECOMMENDED MOTORS DUAL VOLTAGE.

Prong in the attachment piug at the other end. THESE CRAFTSMAN MOTORS HAVE BEEN This plug requires a mating 3-conductor grounded type. • unpacking and heckmg contents: • i ¸. • • • •• • Your: jointer:planer is;shipped: complete in one carton (_thou_: motor or Stand)_ Qty. Separateatl parts from packing materials and check each 1: Jointer-Planer. Item;with illustration and '*Tabie: of Loose Parts'.

• MOUNTING JOINTER-PLANER ON RECOM- MENDED CRAFTSMAN STAND (NOT SUPPLIED IN CANADA) FENCE LOCK See page 27 for recommended stand. KNOB PARTS NEEDED Nuts, Bolts and Washers removed when unpacking Jointer. SCREW 1 - Round Hd.

Screws 1/4 -20x 1/2 in. 4 carriage bolts, 5/16 - 18 x 1 in., flat washers, lock washers Hex. Nuts 1/4- 20 and nuts supplied with Craftsman Stand. 1 Jointer Planer Belt Guard TOOLS NEEDED 1 Motor Pulley Belt Guard. SHAFT PAN HID.

Place motor on your workbench with 5/8 in. Shaft (with key way) facing you. Attach guard support bracket with screws. NOTE: The holes in the bracket are not threaded, the screws are 'thread cutting screws'.

• assembly BELT Install three clips on belt guard 90 ° apart with long tabs pointing AWAY from round opening. Insert belt into open end of guard.

_'_'BELT GUARD CLIPS (90 ° APART) 8. Neo Bomberman Full Game. Snap guard into position as shown.

• Remove knob and washer., lift guard up. Place belt onto Jointer pulley by rotating the pulley. MAKE SURE BELT HAS NOT SLIPPED MOTOR PULLEY. Move motor sideways so that both pulleys are in line. PUSH downward on motor to apply tension to belt and tighten.

• geffing iointer-planer WARNING: FOR YOUR OWN SAFETY TURN SWITCH 'OFF' REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS, FENCE TILT SCALE (BEHIND FENCE):FENCE SLIDING GUARD OUTFEED TABLE KNOB FENCE LOCK 1NFEED TABLE KNOB SLIDE BRACKET:.CUTTER GUARD ON-OFF SWITCH. • FENCE LOCKS AND STOPS. The fence can be moved across the Jointer to take full advantage of the 'sharpness' of the blades. The fence should be positioned to the extreme right (toward pultey) but not beyond the end of the blades. Most of the cutting (usually jointing) will be done.