Fostex Speakers For Sale--The Magic of Full-Range, Single Speaker. The four other Fostex 8 inch full-range speakers do not use a whizzer cone. Apr 27, 2010 Posts about Full-range written. I wanted to build a pair of loudspeakers that was out of the ordinary and involved a. Fostex FE206E 8' Full-range. Audio Nirvana, Lowther, and Fostex Fullrange DIY speaker kits and amplifiers. 3 inches to 15 inches. DIY Audio Full-Range High Efficiency DIY Speakers and Amplifiers.

What is a full range speaker? Activity Based Costing Software Comparison there. Ideally, there will be one driver reproducing the entire audio range (commonly considered to be 20 Hz to 20 kHz).

There will be no crossovers needed, no integration issues between two or more separate drivers, and no time alignment, phase or polarity errors. The output of the amplifier, therefore, would be connected - via the speaker cable of choice - directly to the speaker driver. The result would be extraordinary clarity and freedom from distortion. If this was possible - remember I said 'ideally' - the result would be, quite simply, revolutionary. In the real world, there are many drivers and designs that try to cover as much of the audio range as possible, but usually require complex enclosures to maximize their bass responses.

This project recognized the limitations in current driver technology, and planned for the use of subwoofers from approximately 95 Hz on down. Technical stuff: for a 20 liter, floor standing enclosure for a Fostex 164 (or 168S - see below ) 6' full range driver.

The design goal for this speaker is -3 dB at about 85 Hz to mate with a sub, and control of the limited Xmax through the use of a sealed enclosure. Max SPL (based on Xmax) is around 98-100 dB at the listening seat which is about 8 feet from the plane of the two speakers. The inside is covered with 2 inch 'egg-crate' acoustic foam. Internal wiring is Analysis Plus Oval 12.

There is a built-in sealed 'base', which is filled with about 20 pounds of sand. Spiked feet are used - Remington Power Hammer threaded studs, pn 100760, which have 1/4'-20 threads. The drivers are mounted using T-nuts. All exterior edges, except around the base, are routed with a 1/2' quarter-round bit. The total system weight is 65 pounds per finished speaker. The Qts of the Fostex driver is raised by.12 due to the 3.5 ohm output impedance of the tube amplifier.

This lowers the f3 from 110 Hz to approx. For more information on the Fostex FE164 driver,. You'll see an almost amazingly flat frequency response and good sensitivity of 92 dB, with a minimum impedance of 8 ohms. This sensitivity suggests a driving amplifier of approximately 20-60 watts. I used extensive bracing instead of thick walls, which are 3/4' MDF.

Since opposite walls move in opposite directions, cross bracing IMO is very effective in reducing vibration. I used 8 - 3/4' x 3' x 6 3/4' pieces of MDF placed somewhat randomly. Five of these are in contact with the front and side panels.

There is one placed at a diagonal across the interior of the top. The cabinet plans can accommodate the volume of up to eight of these braces. The goal is to 'create' many small and dissimilar sized panel areas, so that vibration frequencies will be small in amplitude and not concentrated at one frequency. Exhaust Header Design Software Free Download. Random spacing of the cross-braces is very effective for this. The upper rear panel is removable and screwed to a gasketed frame of 2 x 2s.

June, 2002 update: The removable upper rear panel was included for easier access to the interior to add stuffing or make other changes. It turned out that it was not needed. Serial Easy Cd Creator 6 more. If I did this project again, I would not include the removable back. Note: I don't have the tools to cut sheets of wood accurately, so I contacted a local cabinet maker. They supplied the wood and cut it using the drawings above. It took about 45 minutes using their saws, and they charged just $60, including the sheet of MDF.